Product Description

A comprehensive technical manual on the HCIC 7-Ton to 12-Ton Telescopic Dump Trailer Hoist Cylinder (78" Stroke, 3000 PSI), detailing 3,000 PSI continuous operating pressures, 78" to 144" stroke options, front-mount trunnion and pin configurations, 1.6 to 4.6 gallon fluid displacement sizing, SAE #8 ORB leak-free porting, and chassis integration for commercial tandem-axle dump trailers and medium tipper bodies.

Product Detail

In modern commercial dump trailer design (12-foot to 20-foot body lengths), mounting the hoist cylinder at the front bulkhead inside a "doghouse" enclosure provides significant mechanical and structural advantages over traditional underbody scissor hoists:

Item Specification
Cylinder Model HCIC 7–12 Ton Multi-Stage Telescopic Cylinder
Retracted Length 34.75"
Extended Length 112.75"
Stroke 78"
Dump Body Size 12-to-20 ft
Payload Rating 7 to 12 Ton
Mount Style Front Bulkhead Mount
Pivot Point Rear Hinge Pivot

  • True Maximum Leverage Arm: By attaching directly to the front bulkhead, the cylinder utilizes the entire length of the dump body as a lever arm relative to the rear pivot hinge. This minimizes the initial breakout force required to lift a 7-to-12 ton payload compared to an underbody hoist pushing near the middle of the chassis.
  • Elimination of Center-Chassis Frame Sag: Underbody scissor hoists concentrate tens of thousands of pounds of upward thrust into the center of the trailer frame rails, frequently causing structural frame fatigue and weld cracking. Front-mount cylinders distribute lift forces between the front tongue header and the rear pivot, protecting trailer frame integrity.
  • Steep 48° to 52° Clean Dump Angles: With a full 78.0" to 144.0" stroke length extending out to 112"–193", the hoist achieves a steep tipping angle, ensuring sticky clay, wet gravel, and asphalt discharge completely without dangerous manual shovel work.

Specifying the HCIC 7-Ton to 12-Ton Telescopic Dump Trailer Hoist Cylinder guarantees commercial trailer builders a rugged, compact lifting unit engineered specifically for front-mount installations.


I. Hydraulic Displacement & Fluid Volume Sizing (1.6 to 4.6 Gallons @ SAE #8 ORB)

When plumbing the HCIC 7-Ton to 12-Ton Telescopic Dump Trailer Hoist Cylinder into 12V/24V DC or engine-driven PTO hydraulic power units, matching fluid displacement volume is essential:

1. Displacement Volume Sizing (1.6 to 4.6 Gallons): Because multi-stage telescopic sleeves are single-acting or power-up/gravity-down units, fluid displaced during full stroke must be supplied directly from the reservoir tank.

A 78" stroke model requires approximately 1.6 to 2.2 gallons of usable oil.

Longer 120" to 144" stroke models require up to 4.6 gallons of usable hydraulic fluid.

Bodybuilder Rule: Always size the hydraulic reservoir tank to be at least 1.5× the cylinder displacement volume to prevent pump cavitation when the hoist is fully raised at maximum dump angle.

2. SAE #8 ORB (3/4-16 UNF) Leak-Free Porting: Traditional pipe-thread (NPT) ports frequently leak under 3,000 PSI vibration and temperature fluctuations. The HCIC telescopic cylinder features precision SAE #8 O-Ring Boss (ORB) threads, ensuring an elastomeric face-seal that remains 100% leak-free over thousands of high-pressure dumping cycles.


II. Dimensional Sizing Matrix & Sleeve Staging Envelope

The HCIC telescopic dump cylinder series is manufactured in high-strength alloy steel to withstand dynamic road vibrations and off-center payload shifts:

Dimensional Parameter Standard 78" Stroke Model Extended 120"–144" Models Engineering & Sizing Notes
Rated Hoist Capacity 7-Ton Nominal / 12-Ton Class 7-Ton to 12-Ton Class Optimized for 12 ft to 20 ft commercial dump trailers
Operating Working Pressure 3,000 PSI (20.7 MPa) 3,000 PSI (20.7 MPa) Heavy-duty continuous fluid power rating
Retracted Pin-to-Pin Length 34.75" – 35.50" 42.25" – 48.75" Fits compact front bulkhead doghouse enclosures
Total Extended Reach Approx. 112.75" Approx. 162" – 192.75" Delivers 48° to 52° clean tipping angles
Total Stroke Travel 78.0" (1,981 mm) 120.0" – 144.0" (3,657 mm) Multi-stage cascading seamless steel sleeves
Hydraulic Port Standard SAE #8 ORB (3/4-16 UNF) SAE #8 ORB (3/4-16 UNF) Positive O-ring boss sealing against vibration
Hydraulic Oil Requirement 1.6 – 2.2 Gallons 3.2 – 4.6 Gallons Usable reservoir capacity required per cycle
Mounting Architecture Top Pin / Base Trunnion Top Pin / Base Trunnion Accommodates angular tipping rotation
Unit Net Weight 90 kg (198 lbs) 105 – 125 kg (231 – 275 lbs) Solid high-strength seamless alloy steel construction
Shipping Package Size 146 × 41 × 51 cm 175 × 45 × 55 cm Reinforced wooden crate (Gross weight: 120.0 kg)

Trailer manufacturers standardizing on the HCIC 7-Ton to 12-Ton Telescopic Dump Trailer Hoist Cylinder achieve consistent interchangeability across their entire commercial tipper product lines.


III. Field Installation & Trunnion Pin Alignment Checklist

To ensure maximum seal longevity and smooth multi-stage sleeve extension, follow this 4-step workshop installation protocol:

Step 1: Doghouse Bulkhead Clearance Verification: Verify that the trailer front doghouse compartment provides at least 1.5 inches (38 mm) of lateral clearance around the cylinder body throughout its entire angular swing from 0° flat transport to 50° full dump.

Step 2: Trunnion Pin Axis Leveling: Using a precision digital inclinometer, ensure the lower trunnion mount bracket axis is square to the trailer frame rails within ±0.5 mm (±0.05°). Misaligned trunnions induce bending moments that accelerate wear on internal guide bushings.

Step 3: Hydraulic Line Plumbing & Flow Velocity: Connect a minimum 1/2-inch inside diameter high-pressure hose to the SAE #8 ORB port. Avoid restrictive 90-degree street elbows directly at the cylinder port to ensure rapid gravity-down lowering speeds.

Step 4: Bleeding Trapped Air on Initial Commissioning: Fill the hydraulic reservoir, cycle the cylinder through three full stroke extensions at low pressure (< 500 PSI), and allow trapped air to return to the vented reservoir tank.


IV. FAQ

What is the lead time?
Normally 7–15 working days after deposit. Custom orders need to be confirmed separately.
Can you accept custom specifications?
Yes, we support customized stroke, pressure, mounting type and surface treatment for hydraulic cylinders.
What is your payment term?
T/T 30% deposit, balance before shipment. L/C is also available for large orders.
Warranty period?
12 months warranty against manufacturing defects, excluding damage caused by improper operation.


V. Factory-Direct OEM Batch Sourcing from HCIC

Manufactured at HCIC's advanced fluid power production facility in Jinan, Shandong, China, our telescopic dump cylinders undergo 100% full-stroke pressure testing before dispatch:

  • Certified Mechanical Inspection: Full documentation verifying dimensional tolerances, seamless tube concentricity, and seal pressure retention is supplied with every shipment.
  • Live Pre-Shipment Video Inspection: Overseas distributors and trailer OEMs can inspect crated batches, surface finish quality, port threading, and serial number stamping in real time via live video.
  • Standard Heavy-Duty Export Crating: Cylinders are preserved with anti-corrosion VCI wrapping and packed in reinforced 146 cm × 41 cm × 51 cm wooden crates (gross weight: 120.0 kg).
  • 1-Year Commercial Warranty: Backed by HCIC's standard one-year warranty covering material quality, welded structural integrity, and multi-stage seal performance.

Contact Us

Request Your OEM Quotation: To order the HCIC 7-Ton to 12-Ton Telescopic Dump Trailer Hoist Cylinder or request custom pin-to-pin retracted heights (such as 34.75"–35.5"), contact HCIC engineering directly at "info@jnhcic.com".

Products Categorys

Featured Products

Navigation